P1186, P2105 thru P2110 - Inside Angle Fitting (1-5/8" Series)

P1186-No-Dimensions.png
Add to Project Download
Cut Sheet
Part No. A B Finish Product Weight / Piece (lbs)
P1186 45° 3-1/8" (79) EG 0.58
P1186 45° 3-1/8" (79) DF 0.615
P1186 45° 3-1/8" (79) HG 0.615
P1186 45° 3-1/8" (79) GR 0.58
P1186 45° 3-1/8" (79) ZD 0.58
P1186 45° 3-1/8" (79) SS 0.58
P2105 82-1/2° 3-3/16" (81) EG 0.58
P2105 82-1/2° 3-3/16" (81) HG 0.615
P2105 82-1/2° 3-3/16" (81) GR 0.58
P2105 82-1/2° 3-3/16" (81) ZD 0.58
P2106 75° 3-3/16" (81) EG 0.58
P2106 75° 3-3/16" (81) HG 0.615
P2106 75° 3-3/16" (81) GR 0.58
P2106 75° 3-3/16" (81) ZD 0.58
P2107 67-1/2° 3-1/8" (79) EG 0.58
P2107 67-1/2° 3-1/8" (79) HG 0.615
P2107 67-1/2° 3-1/8" (79) GR 0.58
P2107 67-1/2° 3-1/8" (79) PL 0.58
P2107 67-1/2° 3-1/8" (79) ZD 0.58
P2108 60° 3-1/8" (79) EG 0.58
P2108 60° 3-1/8" (79) HG 0.615
P2108 60° 3-1/8" (79) GR 0.58
P2108 60° 3-1/8" (79) ZD 0.58
P2108 60° 3-1/8" (79) SS 0.58
P2109 52-1/2° 3-1/16" (78) EG 0.58
P2109 52-1/2° 3-1/16" (78) HG 0.615
P2109 52-1/2° 3-1/16" (78) GR 0.58
P2109 52-1/2° 3-1/16" (78) ZD 0.58
P2110 37-1/2° 3" (76) EG 0.58
P2110 37-1/2° 3" (76) HG 0.615
P2110 37-1/2° 3" (76) GR 0.58
P2110 37-1/2° 3" (76) ZD 0.58
P2110 37-1/2° 3" (76) SS 0.58

    Angular Design Loads


    Design Loads - P1186, P2105 thru P2110
    Part Number Angle  Average Ultimate Tension
    (lbs)
     Design Tension Load
    (lbs)
    Average Deflection at Design Tension Load
    P2105 82-1/2° 5,800 1,500 0.140"
    P2106 75° 6,000 1,500 0.147"
    P2107 67-1/2° 6,000 1,500 0.179"
    P2108 60° 5,300 1,500 0.189"
    P2109 52-1/2° 5,100 1,500 0.200"
    P1186 45° 4,300 1,400 0.190"
    P2110
    37-1/2° 3,300 1,100 0.158"
     
    Notes:
    1. Design loads only apply to UNISTRUT brand products. Look for "UNISTRUT" on the part.
    2. Design loads are based on static testing with a Safety Factor = 3.5, except for **, based on ultimate strength of connection. **Safety Factor - 3.0.
    3. 1/2" Unistrut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
    4. Design loads limited to 1,500 lbs for Slip Load of Channel Nuts.
    5. Deflection measured in direction of tension load.

    General Specifications

    Standard Dimensions (Unless Shown Otherwise on Drawing):

    • Hole Diameter:  9/16"  (14mm)
    • Hole Spacing (From End):  13/16"  (21mm)
    • Hole Spacing (On-Center):  1 7/8"  (48mm)
    • Width:  1 5/8"  (41mm)
    • Thickness:
    • 1/4"  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

    Note:

    • When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

    Materials & Finishes

    Materials & Finishes - Standard:

    • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
    • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
    • Unistrut Defender (DF):  Conforms to ASTM A1059
    • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
    • Perma-Green (GR):  Conforms to commercial standards for powder coating
    • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1
    • Plain (PL):  No finish 

    Materials & Finishes - Special Metals:

    • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
    • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
    • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

    * These materials have different physical properties and performance characteristics. Please contact us for design support.

    Related Resources

    Videos

    Technical Documents