P1546, P2094 thru P2100 - 2 Hole, Outside Angle Fitting (1-5/8" Series)

P1546-No-Dimensions.png
  • P1546 Table
Add to Project Download
Cut Sheet
Part No. B C Finish Product Weight / Piece (lbs)
P1546 3-9/16" (91) 1-11/16" (43) EG 0.58
P1546 3-1/2" (89) 1-13/16" (46) DF 0.615
P1546 3-1/2" (89) 1-3/4" (44) HG 0.615
P1546 3-9/16" (91) 1-11/16" (43) GR 0.58
P1546 3-1/4" (83) 2-1/16" (52) ZD 0.58
P1546 3-3/8" (86) 1-7/8" (48) SS 0.58
P1546 3" (76) 2-5/16" (59) AL 0.23
P2094 2-11/16" (68) 2-5/8" (67) EG 0.58
P2094 HG 0.615
P2094 GR 0.58
P2094 ZD 0.58
P2095 EG 0.58
P2095 HG 0.615
P2095 GR 0.58
P2096 EG 0.58
P2096 HG 0.615
P2096 GR 0.58
P2096 ZD 0.58
P2097 EG 0.58
P2097 HG 0.615
P2097 GR 0.58
P2097 ZD 0.58
P2097 SS 0.58
P2098 EG 0.58
P2098 HG 0.615
P2098 GR 0.58
P2098 ZD 0.58
P2099 EG 0.58
P2099 HG 0.615
P2099 GR 0.58
P2099 ZD 0.58
P2099 AL 0.23
P2100 EG 0.58
P2100 HG 0.615
P2100 GR 0.58
P2100 ZD 0.58

    Design Loads


     
    Notes:
    1. Design loads only apply to UNISTRUT brand products. Look for "UNISTRUT" on the part.
    2. Average Safety Factor = 4.0 based on static testing to the ultimate strength of connection. Design Loads are limited to 1,500 lbs for Slip Load of Channel Nuts with a Safety Factor = 3.0.
    3. 1/2" Unistrut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
    4. Deflection is the average of straight line interpolations of deflection readings at 1,000 lbs and 2,000 lbs Tension Loads. Deflection is measured in the direction of the Tension Load.

    General Specifications

    Standard Dimensions (Unless Shown Otherwise on Drawing):

    • Hole Diameter:  9/16"  (14mm)
    • Hole Spacing (From End):  13/16"  (21mm)
    • Hole Spacing (On-Center):  1 7/8"  (48mm)
    • Width:  1 5/8"  (41mm)
    • Thickness:
    • 1/4"  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

    Note:

    • When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

    Materials & Finishes

    Materials & Finishes - Standard:

    • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
    • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
    • Unistrut Defender (DF):  Conforms to ASTM A1059
    • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
    • Perma-Green (GR):  Conforms to commercial standards for powder coating
    • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1
    • Plain (PL):  No finish 

    Materials & Finishes - Special Metals:

    • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
    • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
    • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

    * These materials have different physical properties and performance characteristics. Please contact us for design support.

    Related Resources

    Videos

    Technical Documents