P3000HS - 1-5/8" x 1-3/8", 12 Gage, Round Holes
Unistrut's P3000HS has round holes on the back side for use with 1/2" threaded rod and fasteners (or smaller diameters with use of flat washers). These holes can eliminate the need for field drilling when installing a trapeze support, anchoring the channel to a surface, or for many other applications.
This channel is commonly used for trapeze supports, seismic bracing, and anchoring to floors, ceilings and walls. This is a great product for certain seismic bracing applications where slots are not allowed.
Product dimensions are 1 5/8" wide x 1 3/8" tall x 12 ga. thick; with round holes on one side. The holes are 9/16" in diameter and 1 7/8" on center. The hole diameters and spacing match Unistrut’s general fittings so that nearly all our fittings can be attached through these holes.
Our P3000HS is available in the following finishes: Pre-Galvanized (PG), Hot-Dip Galvanized (HG), Plain (PL), Green (GR), Zinc Dichromate (ZD), Stainless Steel (SS) and Aluminum (EA).
|Part No.||Length (ft)||Finish||Product Weight / Ft (lbs/ft)|
|Beam Loading - P3000HS|
Max Allow. Uniform Load
Deflection at Uniform Load
|Uniform Loading at Deflection||Lateral Bracing Reduction Factor|
|Note||NR - Not Recommended|
|Column Loading - P3000HS|
Allowable Load at Slot Face
|Max Column Load Applied at C.G.|
|K=0.65 (lbs)||K=0.80 (lbs)||K=1.0 (lbs)||K=1.2 (lbs)|
Elements of Section
|Elements of Section - P3000HS|
|Area of Section||0.5 in2 (3.2 cm2)|
|Axis 1-1||Axix 2-2|
|Moment of Inertia (I)||0.12 in4 (5 cm4)||0.203 in4 (8.4 cm4)|
|Section Modulus (S)||0.153 in3 (2.5 cm3)||0.250 in3 (4.1 cm3)|
|Radius of Gyration (r)||0.489 in (1.2 cm)||0.638 in (1.6 cm)|
- 10 feet: 10' or 10’ 1/8” (3.05m) ± 1/8" (3 mm)
- 20 feet: 20' or 20’ 3/8” (6.11m) ± 1/8" (3 mm)
- Available with a tolerance of ±1/8" (3 mm). Request quote.
- Many Unistrut channel sections can be supplied with a curve. Click here for our ordering form, specifications, and instructions.
- All beam and column load data pertains to carbon steel and stainless steel channels.
- Load tables apply only to UNISTRUT brand channel. Look for "UNISTRUT" on the product.
- Load tables and charts are constructed to be in accordance with the SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS 2007 EDITION published by the AMERICAN IRON AND STEEL INSTITUTE USING ASD METHOD.
- Loads are based on 33 ksi steel cold formed to 42 ksi.
- Safety Factor to Yield Strength is 1.67 for Beam Loads and 1.80 for Column Loads.
- Beam loads are based on a simple beam and are given as a total uniform load (W) in pounds. For proper calculation procedures, refer to our Beam Load Calculation Guide.
- For bearing loads, reference our Bearing Loads Page.
Materials & Finishes
Materials & Finishes - Standard:
- Pregalvanized (PG): Conforms to ASTM A653 SS GR 33, G90.
- Unistrut Defender (DF): Conforms to ASTM A1046 SS GR 33
- Hot Dip Galvanized (HG): Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM A123
- Perma-Green (GR): Steel conforms to ASTM A1011 SS GR 33, E-Coat finish
- Perma-Gold (ZD): Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM B633, Type II SC3
- Plain (PL): Conforms to ASTM A1011 SS GR 33
- Stainless Steel, Type 304 (SS): ASTM A240, Type 304 *
- Stainless Steel, Type 316 (ST): ASTM A240, Type 316 *
- Aluminum (EA): ASTM B221, Type 6063-T6 (Extruded) *
* These materials have different physical properties and performance characteristics. Please contact us for design support.