P3300SL - 1-5/8" x 7/8", 12 Gage, Long Slots

P3300SL-No-Dimensions.png
Add to Project Download
Resources
Download
Cut Sheet

Unistrut's P3300SL has long slots on the back side for use with 3/8" threaded rod and fasteners. These slots can eliminate the need for field drilling and allow adjustability when installing. The slots are 3" long with 1" spacing.

This channel is commonly used for trapeze supports, seismic bracing, ceiling grids, pipe, conduit, duct and cable tray supports, racks, and other general framing. For application examples, refer to our Application Showcase

Product dimensions are 1 5/8" wide x 7/8" tall x 12 ga. thick; with slots. The slots are 13/32" wide x 3" long, 4" on center and sized for use with 3/8" threaded rod or fasteners.

Our P3300SL is available in the following finishes:  Pre-Galvanized (PG), Hot-Dip Galvanized (HG), Plain (PL), Green (GR), Zinc Dichromate (ZD) and Stainless Steel (SS).
Part No. Length (ft) Finish Product Weight / Ft (lbs/ft)
P3300SL 10 PG 1.3
P3300SL 20 PG 1.3
P3300SL 10 HG 1.314
P3300SL 20 HG 1.314
P3300SL 20 GR 1.3
P3300SL 10 GR 1.3
P3300SL 10 PL 1.3
P3300SL 20 PL 1.3
P3300SL 20 ZD 1.3
P3300SL 10 ZD 1.3
P3300SL 10 SS 1.3
P3300SL 20 SS 1.3

    Beam Loading

    Beam Loading - P3300SL
    Span
    (in)
    Max Allow. Uniform Load
    (lbs)
    Deflection at Uniform Load
    (in)
    Uniform Loading at Deflection Lateral Bracing Reduction Factor
    Span/180
    (lbs)
    Span/240
    (lbs)
    Span/360
    (lbs)
    24 510 0.10 510 510 340 1.00
    36 340 0.22 306 230 153 1.00
    48 255 0.40 170 128 85 1.00
    60 204 0.62 111 85 51 0.98
    72 170 0.89 77 60 34 0.97
    84 145 1.20 60 43 26 0.96
    96 128 1.59 43 34 26 0.94
    108 111 1.96 34 26 17 0.93
    120 102 2.48 26 17 17 0.92
    Refer to the General Specifications for loading information.

    Column Loading

    Column Loading - P3300SL
    Unbraced
    Height
    (in)
    Allowable
    Load at Slot Face
    (lbs)
    Max Column Load Applied at C.G.
    K=0.65 (lbs) K=0.80 (lbs) K=1.0 (lbs) K=1.2 (lbs)
    24 2,360 7,740 7,260 6,350 5,390
    36 2,120 6,470 5,390 3,990 2,810
    48 1,760 4,910 3,550 2,270 1,580
    60 1,380 3,440 2,270 1,460 KL/r>200
    72 1,080 2,390 1,580 KL/r>200 KL/r>200
    Refer to the General Specifications for loading information.

    Elements of Section

    Elements of Section - P3300SL
    Area of Section 0.395 in2 (2.5 cm2)
    Axis 1-1 Axix 2-2
    Moment of Inertia (I) 0.037 in4 (1.5 cm4) 0.143 in4 (6 cm4)
    Section Modulus (S) 0.072 in3 (1.2 cm3) 0.176 in3 (2.9 cm3)
    Radius of Gyration (r) 0.306 in (0.8 cm) 0.601 in (1.5 cm)

    General Specifications

    Standard Lengths:

    • 10 feet:  10' or 10’ 1/8” (3.05m) ± 1/8" (3 mm)
    • 20 feet:  20' or 20’ 3/8” (6.11m) ± 1/8" (3 mm)

    Special Lengths:

    Curved Channel:

    • Many Unistrut channel sections can be supplied with a curve. Click here for our ordering form, specifications, and instructions.

    Load Data:

    • All beam and column load data pertains to carbon steel and stainless steel channels.
    • Load tables apply only to UNISTRUT brand channel. Look for "UNISTRUT" on the product.
    • Load tables and charts are constructed to be in accordance with the SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS 2007 EDITION published by the AMERICAN IRON AND STEEL INSTITUTE USING ASD METHOD.
    • Loads are based on 33 ksi steel cold formed to 42 ksi.
    • Safety Factor to Yield Strength is 1.67 for Beam Loads and 1.80 for Column Loads.
    • Beam loads are based on a simple beam and are given as a total uniform load (W) in pounds. For proper calculation procedures, refer to our Beam Load Calculation Guide.
    • For bearing loads, reference our Bearing Loads Page.

    Materials & Finishes

    Materials & Finishes - Standard:

    • Pregalvanized (PG):  Conforms to ASTM A653 SS GR 33, G90.
    • Unistrut Defender (DF):  Conforms to ASTM A1046 SS GR 33
    • Hot Dip Galvanized (HG):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM A123
    • Perma-Green (GR):  Steel conforms to ASTM A1011 SS GR 33, E-Coat finish
    • Perma-Gold (ZD):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM B633, Type II SC3
    • Plain (PL):  Conforms to ASTM A1011 SS GR 33
    Materials & Finishes - Special Metals:
    • Stainless Steel, Type 304 (SS):  ASTM A240, Type 304 *
    • Stainless Steel, Type 316 (ST):  ASTM A240, Type 316 *
    • Aluminum (EA):  ASTM B221, Type 6063-T6 (Extruded) *

    * These materials have different physical properties and performance characteristics. Please contact us for design support.